Jump to content

Leaderboard


Popular Content

Showing content with the highest reputation since 03/24/2018 in all areas

  1. 4 points
    Hi guys just wanted to post some images of a few things I've been working on. I've built myself my very own crypto room. I built the entire lot, and proved to be a lot of work, but well worth it. Just wanted to share my work. Framing up of the room Installation of exterior sheeting Flushed exterior joins Installation of insulation Door frame installed Exhaust fan to remove heat in the room Walls flushed Installation of floor Laying of carpet tiles Fitting off data rack Denarius wall logo WIP First I used a projector to project the logo on the wall. Masking tape was used in the wall followed by a scalpel knife to cut out the lettering followed by painting. Job complete - I've also been working along side Buzz who had helped me get a full screen QT Wallet running on the raspberry Pi 3b+ The wallet runs perfectly on the pi 👌 I decided I needed a bit of colour on the wall along side the Denarius logo so managed to get a copy of an image of Denario, the D mascot. Thanks for stopping by Wookie
  2. 4 points
  3. 3 points
    Yea way epic, when are we going to make this our headquarters? Haha really awesome work man! Impressive to say the least!
  4. 2 points
    Wookie bro you did an amazing job, build me a house bro! Lol Buzz killed it on the pi installation!! Absolutely blown away!
  5. 2 points
    Great work!! you are my new hero!! ! really impressed 😮
  6. 2 points
    I think I know what coin chart you can put on the 2nd TV. 🤑
  7. 2 points
    Extra D Tip If you are up for the task. On your vps, add staking=1 to denarius.conf, restart wallet, then denariusd getnewaddress Send a little amount so your VPS wallet is staking, even 1 D will do something over time.
  8. 2 points
  9. 2 points
    Firstly, thanks to everyone on DenariusTalk and the Discord (especially Carsen) who has put up with my persistent questions and helped out with this project over the past few weeks. Hopefully this article will make it all worth it. Over the last month I have learned how to build my own stake box using a Raspberry Pi. Prior to doing this I had no practical knowledge of Raspberry Pi's or Linux whatsoever. It has been a steep learning curve! I looked at lots of different PoS cryptocurrencies and for a number of reasons decided to use Denarius to illustrate the example. While the primary goal is to help an absolute newbie build their own stake box, the guide may also encourage more people to get involved with Denarius, so feel free to share it around. https://steemit.com/cryptocurrency/@nzcrypto/guide-how-to-build-a-cryptocurrency-proof-of-stake-mining-box-for-absolute-newbies
  10. 2 points
    Denarius is taking donations to list on cryptobridge. (1 BTC Total needed.) https://blockchain.info/address/1GgFMs1rTNoZ25eL5eVRy1yvAVeqFJT52N ONLY .46BTC is needed To entice our community to donate we are hosting a 350 DNR giveaway!!! To be eligible to enter, all you have to do is post your TXID of .01BTC of higher here. Once we reach our goal we will randomly select winners: 1st Place: 200 DNR 2nd Place: 100 DNR 3rd Place: 50 DNR
  11. 2 points
    I just noticed some custom DNR Adresses beginning like DNRHodlxxxx.... or DBUZZKixxx... How to do this? THX!
  12. 2 points
    This is my first time rapping and it is about my favorite coin DNR Lyrics: Song Title: soyboy in the house Lyrics: Soy boy in the house Listen up, listen up Stop being a beta Say no being a normie pleb Ditch the starcuck latte Gonna tell you how to be alpha Is all about denarius Gonna put in the hashrate Gonna get the masternode Gonna be the king Cuck cuck cuck Denarius gonna save you https://drive.google.com/open?id=1RZi81vh9zu9RyfLFUwTTKTiYJP8Qo7YOrk264iE3xx4 Song https://drive.google.com/open?id=1m6-0O5xqP8t4NA_9o4uGEZ_8n2lDQUfW My dnr address: D8LUsjCjrJoChxRUfjzqgXjTqdRtRvNNEK Hope you guys donate generously since it is pretty embarassing soyboi in the house.m4a
  13. 2 points
    WHEW! OK. Did a scanforalltxns and it fixed it.
  14. 1 point
    Basic setup to building your own custom Raspbian Image from the offician pi-gen repo using you Denarius daemon wallet as the example. I like that someone can build completely from source and compile the entire OS on their own for their precious crypto. https://github.com/buzzkillb/denariianpi-gen Go to https://github.com/RPi-Distro/pi-gen. Read this a few times how it works. I am using Windows 10, so I downloaded VirtualBox and created an Ubuntu 16.04 VM with 2 cpu's, 100GB hard drive, and 3GB of ram. git clone https://github.com/RPi-Distro/pi-gen You want to build the stock image to make sure this works from the get go. nano config Put this one line in for your image name, ex. testimage IMG_NAME='testimage' Once this is done building you can find the image in the work folder with a date and name of image. The image is in /pi-gen/work/date-imagename/export-image For the first run I wanted to build only the lite command line Raspbian with denariusd daemon. This is found in stage2 directory. I made a new directory called 04-denariusd. And put the files required in there. cd ~/pi-gen/stage2 mkdir 04-denariusd cd 04-denariusd nano 00-packages dependencies to compile denariusd and openssl 1.0.1j git unzip libdb++-dev libboost-all-dev libqrencode-dev libminiupnpc-dev libevent-dev autogen automake libtool Next create a file to compile openssl 1.0.1j and denariusd. nano 04-run.sh #!/bin/bash -e on_chroot << EOF apt-get install make wget https://www.openssl.org/source/openssl-1.0.1j.tar.gz tar -xzvf openssl-1.0.1j.tar.gz cd openssl-1.0.1j ./config make depend make # make test make install sudo ln -sf /usr/local/ssl/bin/openssl `which openssl` git clone https://github.com/carsenk/denarius cd denarius git checkout v3.4 git pull cd src OPENSSL_INCLUDE_PATH=/usr/local/ssl/include OPENSSL_LIB_PATH=/usr/local/ssl/lib make -f makefile.arm strip denariusd cp denariusd /usr/local/bin/denariusd EOF chmod +x 04-run.sh Now the basic setup is done. Go back to ~/pi-gen, run some commands to skip stages after stage2 and run the build command. # Example for building denariian lite system touch ./stage3/SKIP ./stage4/SKIP ./stage5/SKIP touch ./stage4/SKIP_IMAGES ./stage5/SKIP_IMAGES sudo ./build.sh Grab your image from /pi-gen/work/date-imagename/export-image, etch to microsd card and go tinker away with your raspberry pi. tip: this is a really easy way to cross compile for your raspberry pi. This uses qemu so you get 1 cpu and minimal ram, but outside of compiling everything else is maxing out the VM.
  15. 1 point
    Run the following commands to compile Denarius properly without errors on Ubuntu 18.04+ (Ubuntu changed their sources list for the dep "libssl-dev", you will need to install an older version of OpenSSL to be able to compile Denarius) Make sure to remove the current libssl-dev: sudo apt-get remove libssl-dev Install an older version of OpenSSL, for this we use 1.0.1j wget http://www.openssl.org/source/openssl-1.0.1j.tar.gz tar xvfz openssl-1.0.1j.tar.gz cd openssl-1.0.1j cd openssl-1.0.1j ./config make -j(number of cores) That should get the older version installed. Also you may want to symlink openssl still: sudo mv /usr/bin/openssl /root/ sudo ln -s /usr/local/ssl/bin/openssl /usr/bin/openssl openssl version (To check the openssl version installed) Also you will want to run these when you run qmake again qmake "USE_UPNP=1" "USE_QRCODE=1" OPENSSL_INCLUDE_PATH=/usr/local/ssl/include OPENSSL_LIB_PATH=/usr/local/ssl/lib denarius-qt.pro Then you should be good for Ubuntu 18.04 Denarius compiling and it should compile with no errors , otherwise all other older Ubuntu versions you can just do the usual sudo apt-get install libssl-dev
  16. 1 point
    FortunaStake Setup Guide ... This will take 500 confirms before being able to start, so do the send first, then read through the guide. Send exactly 5000 D to an address and give that address a label like FS01. Script for VPS Portion Located Here This will pull master branch and compile the latest wallet. And add a cronjob to restart wallet every hour to make sure things stay in sync. https://github.com/buzzkillb/d-fortunastake QT Wallet After sending 5000 D to a labelled address, we need the following; transaction hash and index of the 5000 send, fortunastake private key, and your VPS IP address. FS01 VPSIPADDRESS:9999 FORTUNASTAKEPRIVKEY TRANSACTIONHASH INDEXNUMBER Sample fortunastake.conf FS01 11.11.12.13:9999 6J8tAUsVhXBgfdeewqsdghySWEQEeb4XGSC251sM7bYQgEXh7 f08d926f92cc4c65321344828f6394f41121903502459ffde4ef7aef39e6392b 0 fortunastake private key fortunastake genkey fortunastake transaction hash and id fortunastake outputs VPS of your ip should be somewhat obvious. After creating your fortunastake.conf, save and restart the QT wallet. Sample QT denarius.conf fsconflock=1 staking=1 Now that address has locked the 5000 D collateral. VPS Get a VPS from somewhere like Vultr, make note of its IP address for the above fortunastake.conf creation for the QT wallet. On the VPS Update Linux sudo apt-get update && apt-get upgrade -y Install Dependencies sudo apt-get install -y git unzip build-essential libssl-dev libdb++-dev libboost-all-dev libqrencode-dev libminiupnpc-dev libgmp-dev libevent-dev autogen automake libtool Install Fail2Ban sudo apt install fail2ban Create Swap File sudo fallocate -l 2G /swapfile sudo chmod 600 /swapfile sudo mkswap /swapfile sudo swapon /swapfile echo '/swapfile none swap sw 0 0' | sudo tee -a /etc/fstab Install Firewall sudo apt install ufw -y ufw default allow outgoing ufw default deny incoming ufw allow ssh/tcp ufw limit ssh/tcp ufw allow 33369/tcp ufw allow 9999/tcp ufw logging on ufw --force enable Compile and Install Wallet (most likely need to add swapfile below) git clone https://github.com/carsenk/denarius cd denarius git checkout master cd src make -f makefile.unix sudo mv ~/denarius/src/denariusd /usr/local/bin/denariusd Install Chaindata apt-get -y install unzip mkdir ~/.denarius cd ~/.denarius rm -rf database txleveldb smsgDB wget https://github.com/carsenk/denarius/releases/download/v3.3.7/chaindata1701122.zip unzip chaindata1701122.zip Create denarius.conf in the .denarius folder. Notice the . in the folder name. denarius.conf rpcuser=USEARANDOMNAME rpcpassword=USEARANDOMPASSWORD daemon=1 port=9999 fortunastake=1 fortunastakeprivkey=6J8tAUsVhXBgfdeewqsdghySWEQEeb4XGSC251sM7bYQgEXh7 run denariusd by typing denariusd Start Go back to your QT, go to debug console and type. fortunastake start-alias FS01 In the My Denarius Fortuna Stakes tab in your QT collateral wallet, the QT will show Registered once you start your FortunaStake and then Verified, then Online, then Active. Wait 1 complete round for rewards. 1 round is roughly how many ForTunaStakes are up, and that's how many blocks a round will last. Status Check masternode status still works for specific reasons, but fortunastake status gives info in English instead of numbers and gibberish. fortunastake status
  17. 1 point
    Single USB and ethernet port looks perfect for a headless server. Just about ready to buy one of these!😍
  18. 1 point
    I edit the logo in GIMP by first resizing the image to 54x54 pixels, then adjust canvas size to 212x104 pixels and drag the logo to where I want it located.
  19. 1 point
    Now you want to throw Bitcoin Price into your new Cryptocurrency scroller? Pulling API info from coindesk. btcprice.py #!/usr/bin/env python # -*- coding: utf-8 -*- import urllib, json from inky import InkyPHAT inky_display = InkyPHAT("yellow") inky_display.set_border(inky_display.YELLOW) from PIL import Image, ImageFont, ImageDraw print("""Inky pHAT: Bitcoin Price information. """) img = Image.new("P", (inky_display.WIDTH, inky_display.HEIGHT)) draw = ImageDraw.Draw(img) from font_fredoka_one import FredokaOne font = ImageFont.truetype(FredokaOne, 24) url = "https://api.coindesk.com/v1/bpi/currentprice.json" response = urllib.urlopen(url) data = json.loads(response.read()) chartname = data['chartName'] btcusd = data['bpi']['USD']['rate_float'] btceur = data['bpi']['EUR']['rate_float'] bitcoinprice = (chartname + '\n' + "$ " + str(btcusd) + '\n' + "E " + str(btceur)) # Load our backdrop image img = Image.open("/home/pi/btc_yellow.png") draw = ImageDraw.Draw(img) draw.text((10, 10), bitcoinprice, inky_display.YELLOW, font) inky_display.set_image(img) inky_display.show() Sample yellow bitcoin logo I am using.
  20. 1 point
    Kind of silly how it works to add an image, but basically follow their own guide how to create this in GIMP. Also be aware the canvas size has to be 212x104 pixels. Make it woooork. https://learn.pimoroni.com/tutorial/sandyj/getting-started-with-inky-phat from inky import InkyPHAT inky_display = InkyPHAT("yellow") inky_display.set_border(inky_display.WHITE) from PIL import Image, ImageFont, ImageDraw img = Image.open("/home/pi/inkyD.png") inky_display.set_image(img) inky_display.show() Sample GIMP png for testing.
  21. 1 point
    Compiling the commits as I see them, QT and Daemon. Takes a bit of time on any version of pi3. 🤖 https://github.com/buzzkillb/denarius-pi3/releases
  22. 1 point
    How to compile denariusd daemon on Raspberry Pi3 in Raspbian and run TOR. Headless Install (enable wifi and enable ssh) https://desertbot.io/blog/headless-raspberry-pi-3-bplus-ssh-wifi-setup Swap Space (Required for Compiling) https://www.bitpi.co/2015/02/11/how-to-change-raspberry-pis-swapfile-size-on-rasbian/ sudo sed -i 's/CONF_SWAPSIZE=100/CONF_SWAPSIZE=2048/' /etc/dphys-swapfile sudo /etc/init.d/dphys-swapfile stop sudo /etc/init.d/dphys-swapfile start free -m On dependencies read a few posts below if you want to compile and use berkeley database 4.8 to keep backwards compatibility. sudo apt-get update -y && sudo apt-get upgrade -y sudo apt-get --assume-yes install git unzip build-essential libdb++-dev libboost-all-dev libqrencode-dev libminiupnpc-dev libgmp-dev libevent-dev autogen automake libtool Compile and replace openssl to openssl 1.0.1j. (may or may not be required) I need to double check if there was 1 more step to this or not to make sure openssl is right. apt-get install make wget https://www.openssl.org/source/openssl-1.0.1j.tar.gz tar -xzvf openssl-1.0.1j.tar.gz cd openssl-1.0.1j ./config make depend make #make test make install sudo ln -sf /usr/local/ssl/bin/openssl `which openssl cd ~ openssl version -v Git clone v3.4 branch to get v3.3.8. git clone https://github.com/carsenk/denarius cd denarius git checkout v3.4 git pull cd src OPENSSL_INCLUDE_PATH=/usr/local/ssl/include OPENSSL_LIB_PATH=/usr/local/ssl/lib make -f makefile.arm strip denariusd sudo cp denariusd /usr/local/bin/denariusd #Use Chaindata cd ~ mkdir ~/.denarius wget https://github.com/carsenk/denarius/releases/download/v3.3.6/chaindata1612994.zip unzip chaindata1612994.zip #Install TOR service sudo apt-get install tor sudo nano /etc/tor/torrc Find this line and change the 2 #HiddenServiceDir /var/lib/tor/hidden_service/ #HiddenServicePort 80 127.0.0.1:80 HiddenServiceDir /var/lib/tor/hidden_service/ HiddenServicePort 33369 127.0.0.1:33369 sudo service tor restart #To get onion address sudo cat /var/lib/tor/hidden_service/hostname example from above favlp6mro3bh5jnt.onion #sample TOR and clearnet denarius.conf rpcuser=denariusrpc rpcpassword=STRONGPASSWORD rpcallowip=127.0.0.1 daemon=1 tor=127.0.0.1:9050 listen=1 externalip=favlp6mro3bh5jnt.onion discover=1
  23. 1 point
    stage 3, qt wallet place hodler #02-denariusqt folder layout #wallpaper pi-gen/stage3/02-denariusqt/files/Lava-PI-2.jpg nano 00-packages libqt5gui5 libqt5core5a libqt5dbus5 qttools5-dev qttools5-dev-tools qt5-default nano 05-run.sh Throw in custom denarius lava pi by icanhaz and setup the Denarius QT compile. After compile copy Denarius binary to user pi desktop. #!/bin/bash -e install -m 644 files/Lava-PI-2.jpg "{ROOTFS_DIR}/usr/share/rpd-wallpaper/" on_chroot << EOF cd denarius export QT_SELECT=qt5 qmake -v qmake "USE_NATIVETOR=-" "USE_UPNP=1" "USE_QRCODE=1" OPENSSL_INCLUDE_PATH=/usr/local/ssl/include OPENSSL_LIB_PATH=/usr/local/ssl/lib denarius-qt.pro make cp Denarius /home/pi/Desktop/Denarius EOF chmod +x 05-run.sh
  24. 1 point
    Mental Note Iif you want to use berkeley db 4.8 to always be backwards compatible. Instead of sudo apt-get install libdb++-dev, do this mkdir ~/Downloads cd ~/Downloads wget http://download.oracle.com/berkeley-db/db-4.8.30.NC.tar.gz tar -xzvf db-4.8.30.NC.tar.gz cd db-4.8.30.NC/build_unix/ ../dist/configure --enable-cxx make sudo make install
  25. 1 point
    A list of some onion seeds to connect into if you try the above TOR portion. edit denarius.conf and add these nodes. https://raw.githubusercontent.com/buzzkillb/denarius-qt/master/onion nodes
  26. 1 point
    If anyone just wants to try the v3.3.8 binary that I compiled earlier. wget https://triforce.black/d/denariusd chmod +x denariusd sudo cp denariusd /usr/local/bin/denariusd run denariusd from anywhere denariusd
  27. 1 point
    Use Hive Shell to Update Nvidia Drivers. Expect this to take 30+ minutes on a USB install. https://forum.hiveos.farm/t/nvidia-drivers-update-guide-and-cuda-10/10921 Select Remote Access -> Hive Shell Start Select Hive Shell and click the Web Link. Type in nvidia-driver-update at the command prompt. nvidia-driver-update Getting the latest Nvidia Drivers from HiveOS. Once this finishes you will get a prompt to reboot. Go back to your other tab, hit the Power button -> Reboot. Say hello to the latest drivers. If you went from Cuda 9.2 to Cuda 10.0, don't forget to redo your miner to correct Cuda version.
  28. 1 point
    Try changing the line in your denarius-qt.pro file in the QMAKE FLAGS at the top from c99 to gnu99 and then making again Also ensure you have the Tor deps installed (sudo apt-get install libevent-dev)
  29. 1 point
    We need a dearnius meme/media package. This is what I have in my computer atm
  30. 1 point
    Hi. My wallet stopped syncing a few days ago on block 8001003 and i have no idea why. The worst part is that i have sent some coins to the wallet after this block so they have not arrived. can anyone help? bearing in mind i'm not a programmer and have limited IT skills. I literally need a step by step idiots guide on how to fix this. I'm running v2.5.2.0 This is the debug log file. ERROR: AcceptBlock() : rejected by hardened checkpoint lock-in at 800104 ERROR: AcceptBlock() : rejected by hardened checkpoint lock-in at 800104 ERROR: ProcessBlock() : AcceptBlock FAILED Misbehaving: 134.249.127.120:60418 (0 -> 100) DISCONNECTING disconnecting node 134.249.127.120:60418 connection from 134.249.127.120:57692 dropped (banned) ERROR: FetchInputs() : 324bfd3d58 mempool Tx prev not found 38d1d94603 stored orphan tx 324bfd3d58 (mapsz 67) ERROR: AcceptBlock() : rejected by hardened checkpoint lock-in at 800104 ERROR: ProcessBlock() : AcceptBlock FAILED Misbehaving: 188.223.84.148:33339 (0 -> 100) DISCONNECTING disconnecting node 188.223.84.148:33339 net: trying connection 54.39.50.173:33339 lastseen=127.6hrs net: connected 54.39.50.173:33339 send version message: version 25213, blocks=800103, us=90.196.98.182:33339, them=54.39.50.173:33339, peer=54.39.50.173:33339 socket closed disconnecting node 54.39.50.173:33339 net: trying connection 37.112.127.165:33339 lastseen=127.6hrs connection timeout net: trying connection 54.36.45.67:33339 lastseen=127.5hrs connection timeout net: trying connection 105.8.7.193:33339 lastseen=127.6hrs connection timeout net: trying connection 5.9.98.144:33339 lastseen=127.2hrs accepted connection 89.216.114.157:55945 send version message: version 25213, blocks=800103, us=90.196.98.182:33339, them=89.216.114.157:55945, peer=89.216.114.157:55945 receive version message: version 21213, blocks=887979, us=90.196.98.182:33339, them=89.216.114.157:33339, peer=89.216.114.157:55945 net: received verack from peer version 21213 (recvVersion: 21213) at 89.216.114.157:55945 connection timeout net: trying connection 87.123.33.168:33339 lastseen=127.6hrs ERROR: AcceptBlock() : rejected by hardened checkpoint lock-in at 800104 ERROR: ProcessBlock() : AcceptBlock FAILED Misbehaving: 173.24.196.192:33339 (0 -> 100) DISCONNECTING disconnecting node 173.24.196.192:33339 connection timeout net: trying connection 103.232.209.140:33339 lastseen=127.6hrs net: connected 103.232.209.140:33339 send version message: version 25213, blocks=800103, us=90.196.98.182:33339, them=103.232.209.140:33339, peer=103.232.209.140:33339 socket closed disconnecting node 103.232.209.140:33339 net: trying connection 39.119.94.221:33339 lastseen=127.5hrs socket recv error 10054
  31. 1 point
    The wallet can sync from block 1 though.
  32. 1 point
    How to use the Split UTXO in the QT Wallet First turn on coin control so you can send from specific inputs. My current goal is instead of staking with 500 addresses, to stake with 500 inputs on a single address. Select what inputs or addresses you want to send from. In this case I have a large single input I want to spread out. Specifiy the address that exists in your QT wallet to send to. Checkmark Split UTXO. And type how many inputs you want to spread out to. After that, right click the after fee amount and paste into send amount. Wait for the transaction to have 10 confirms and you are done. Use https://www.coinexplorer.net/D to check your address, then click See Address Unspent Outputs to see your new inputs getting ready to stake.
  33. 1 point
    This is a very easy way to track addresses from your android phone. Like watching masternode payments live. Download Coldfolio from https://whopper.io/ which links to the Google Play Store. Add a card Select your Crypto from the List Scan QR Code from the Denarius QT Wallet go to receive tab, click address and then click below Show QR Code Label your Card in Coldfolio and double check you only have the address This example shows the ?label=MN2, delete this part. This can always be modified later by hodling down the card and clicking modify. Keep track of your staking, masternodes, balances.
  34. 1 point
    @Carsen @buzzkillb For future reference (I plan to help my friend with getting his own wallet sorted) should I follow buzzkillb's updated instructions, or use Carsen's original instructions? Or no matter?
  35. 1 point
    If you download the attached .GIF file and create timestamp, you should get this same address. https://www.coinexplorer.net/DNR/address/DPNrLaRbpgLPMTMLv72Yy3MLpsjNd7jyEW
  36. 1 point
    Updated options to also update to latest precompiled binary wallet.
  37. 1 point
    A quick how to guide for using Hyperdex to atomic Swap between Denarius and Bitcoin. Download Hyperdex https://github.com/lukechilds/hyperdex/releases During registration of your account, you will be asked to write the seed down and store safely. **STORE THIS SEED SAFELY!** After registering account you will end up at this screen. Now select Denarius and deposit DNR into the address shown. 3 small sends are encouraged from the next step. Click exchange and this window pops up. You want to send 3 small transactions. At the Exchange screen select Denarius and Bitcoin. In this example I am selling 1 DNR for 0.00040000 or 40k satoshis. In this example I only sent a single transaction of 10 DNR. I get the error message of not enough UTXO. I already sent 2 more transactions while doing this to show what happens if you don't send a few. Wait for your 3 transactions to fully send in and show up as your total DNR balance. Wait for a moment to see the order pop up on the DNR Sell Orders list. This current hyperdex release is still alpha so expect the unexpected. https://denarius.io/ - Homepage https://discord.gg/YMWMgZe - Discord Community Chat https://denarius.host/ - Masternode Stats http://denarius.win/ - Masternode ROI Stats https://denariustalk.org - Forums
  38. 1 point
    probably missing something here. QT wallet run in debug console masternode start-alias MNDNR
  39. 1 point
    You want to grab the VanityGen Plus from here: https://github.com/exploitagency/vanitygen-plus/releases You can then use it to generate custom Denarius addresses There is also this older guide for DNR addresses:
  40. 1 point
    Added sp-hash. https://github.com/sp-hash?tab=repositories https://github.com/sp-hash/suprminer/releases
  41. 1 point
    You want to be running v2.5, there is currently a known cosmetic balance bug issue if you are staking coins. This has been addressed and will be fixed in the upcoming update v2.5.2 If you are fully synced and running v2.5, you can run the commands repairwallet or scanwalletfortxns If you are having trouble syncing, make sure you grab the latest v2.5 nodes from https://chainz.cryptoid.info/dnr/#!network and if you get stuck, remove your old chaindata from your Denarius data directory.
  42. 1 point
    Hey. Tell me how to set up DNR in solo mining?
  43. 1 point
    Removed some pools, took the latest pool list from the bitcointalk ANN.
  44. 1 point
    Grab our latest v2.5 wallet, a lot of these issues were resolved!
  45. 1 point
    All of the above issues that were reported with syncing and lag were fixed! Download and grab Denarius v2.5! (You will sync much faster now)
  46. 1 point
    I would suggest to replace huobi.pro instead of bithumb. those exchanges with similar volume but huobi.pro is easier and better..
  47. 1 point
    Thanks Carsen! That worked.
  48. 1 point
    Hi everyone I withdrew my DNR from Cryptopia to my wallet 3 days ago and I still see zero balance on my wallet. The wallet appears ok but has been super slow syncing. So I downloaded the latest chaindata.zip file today and it is now fully syncd. However I still have zero balance in my wallet. The transaction id in the block explorer confirms they are in my wallet address. Any ideas?
  49. 1 point
    Personally i'm going to be implementing this into my gem shop eventually through various ways aside from just accepting it as payment, it's the perfect currency for business transactions, fast and cheap to send.
  50. 1 point
    Ok, so I extracted the chaindata into my Denarius folder, wallet seems synced now, BUT, it's empty. Update: ran "repairwallet" in the debug window and restarted, and my coins are back.
×
×
  • Create New...